Skip to main content

Publisher widget

Embed MAXScanner Calculator

Preview it, choose a layout, copy the HTML, and paste it into WordPress, Webflow, Wix, Squarespace or any page that accepts custom HTML.

Copy-ready HTML

Responsive, lazy-loaded and branded with a visible MAXScanner attribution link.

Open standalone
The widget is free to use and stays updated from MAXScanner. Keep the visible branded attribution intact. Browse all embeddable calculators.

Find your next tool

Everyday Planning Calculators

Angle Weight Calculator — Equal & Unequal Angle kg/m

Calculate angle iron and steel angle weight from both leg sizes, thickness, length and density. Get kg/m, lb/ft, batch mass, cost and target-piece reverse solving.

Live calculationWorking shown

Editable live calculator

Change any input — the result updates immediately

No hidden assumptions. Inputs, units and the working stay visible so you can check the calculation.

Calculated result

223.73 kg · 493.23 lb

3.7288 kg/m · 2.5056 lb/ft

475 mm² ideal sharp-corner L-section area · 22.373 kg per piece

Enter rate/kg for procurement cost

Enter target mass for reverse whole-piece count

Enter supplier kg/m to compare nominal/table mass

Show the working
  1. 1. Area = (50 + 50 − 5) × 5 = 475 mm².
  2. 2. Unit mass = 475 × 10⁻⁶ × 7,850 = 3.7288 kg/m.
  3. 3. Piece mass = 3.7288 × 6 = 22.373 kg.
  4. 4. Batch mass = 22.373 × 10 = 223.725 kg.

This is ideal sharp-corner geometry. Rolled angles have root/toe radii and manufacturing tolerances, so standard or mill-table mass can differ. Use certified section data for structural design, contractual mass or lifting-critical work.

More actions

Shared links reopen these inputs. Recent and saved calculations stay in this browser unless you clear site data.

Angle weight chart: kg/m and lb/ft of ISA, European L and US L angles

Under IS 808:2021 an ISA 50 × 50 × 6 equal angle weighs 4.49 kg/m (3.02 lb/ft), an ISA 75 × 75 × 6 weighs 6.86 kg/m and the unequal ISA 75 × 50 × 6 weighs 5.68 kg/m. The European L 50 × 50 × 5 weighs 3.77 kg/m. US angles are named by both legs and the thickness in inches: an L5×5×1/2 weighs 16.2 lb/ft (24.11 kg/m). For one length, multiply: a 6 m ISA 50 × 50 × 6 weighs 26.94 kg. Pick the same angle in the calculator above to add quantity and cost.

ISA equal angles, IS 808:2021 Table 9
Sectionkg/mlb/ft
ISA 20 × 20 × 30.90.6
ISA 20 × 20 × 41.160.78
ISA 25 × 25 × 31.140.77
ISA 25 × 25 × 41.480.99
ISA 25 × 25 × 51.81.21
ISA 30 × 30 × 31.380.93
ISA 30 × 30 × 41.81.21
ISA 30 × 30 × 52.21.48
ISA 35 × 35 × 31.621.09
ISA 35 × 35 × 42.111.42
ISA 35 × 35 × 52.591.74
ISA 35 × 35 × 63.062.06
ISA 40 × 40 × 31.861.25
ISA 40 × 40 × 42.441.64
ISA 40 × 40 × 52.992.01
ISA 40 × 40 × 63.542.38
ISA 45 × 45 × 32.11.41
ISA 45 × 45 × 42.751.85
ISA 45 × 45 × 53.392.28
ISA 45 × 45 × 64.012.69
ISA 50 × 50 × 32.341.57
ISA 50 × 50 × 43.082.07
ISA 50 × 50 × 53.792.55
ISA 50 × 50 × 64.493.02
ISA 55 × 55 × 43.42.28
ISA 55 × 55 × 54.192.82
ISA 55 × 55 × 64.973.34
ISA 55 × 55 × 86.484.35
ISA 60 × 60 × 43.712.49
ISA 60 × 60 × 54.583.08
ISA 60 × 60 × 65.443.66
ISA 60 × 60 × 87.14.77
ISA 65 × 65 × 44.032.71
ISA 65 × 65 × 54.983.35
ISA 65 × 65 × 65.913.97
ISA 65 × 65 × 87.735.19
ISA 70 × 70 × 55.383.62
ISA 70 × 70 × 66.394.29
ISA 70 × 70 × 88.375.62
ISA 70 × 70 × 1010.296.91
ISA 75 × 75 × 55.773.88
ISA 75 × 75 × 66.864.61
ISA 75 × 75 × 896.05
ISA 75 × 75 × 1011.077.44
ISA 80 × 80 × 67.364.95
ISA 80 × 80 × 89.656.48
ISA 80 × 80 × 1011.887.98
ISA 80 × 80 × 1214.059.44
ISA 90 × 90 × 68.325.59
ISA 90 × 90 × 810.927.34
ISA 90 × 90 × 1013.479.05
ISA 90 × 90 × 1215.9510.72
ISA 100 × 100 × 69.266.22
ISA 100 × 100 × 812.188.18
ISA 100 × 100 × 1015.0410.11
ISA 100 × 100 × 1217.8311.98
ISA 110 × 110 × 813.49
ISA 110 × 110 × 1016.5811.14
ISA 110 × 110 × 1219.6813.22
ISA 110 × 110 × 1625.7117.28
ISA 130 × 130 × 815.9210.7
ISA 130 × 130 × 1019.7213.25
ISA 130 × 130 × 1223.4515.76
ISA 130 × 130 × 1630.7420.66
ISA 150 × 150 × 1022.9315.41
ISA 150 × 150 × 1227.2918.34
ISA 150 × 150 × 1635.8424.08
ISA 150 × 150 × 2044.1229.65
ISA 200 × 200 × 1236.8524.76
ISA 200 × 200 × 1648.5332.61
ISA 200 × 200 × 2059.9640.29
ISA 200 × 200 × 2573.949.66
ISA unequal angles, IS 808:2021 Table 11 (a selection; every size is in the picker)
Sectionkg/mlb/ft
ISA 30 × 20 × 31.140.77
ISA 40 × 25 × 41.961.32
ISA 45 × 30 × 52.791.87
ISA 50 × 30 × 52.992.01
ISA 60 × 40 × 53.792.55
ISA 65 × 45 × 64.963.33
ISA 70 × 45 × 65.213.5
ISA 75 × 50 × 65.683.82
ISA 75 × 50 × 87.424.99
ISA 80 × 50 × 65.923.98
ISA 90 × 60 × 89.016.05
ISA 100 × 65 × 89.976.7
ISA 100 × 75 × 810.617.13
ISA 125 × 75 × 812.198.19
ISA 125 × 75 × 1015.0510.11
ISA 125 × 95 × 1016.5411.11
ISA 150 × 115 × 1223.9616.1
ISA 200 × 100 × 1227.2918.34
ISA 200 × 150 × 1642.1828.34
European L equal angles (a selection; every size is in the picker)
Sectionkg/mlb/ft
L 25 × 25 × 31.120.75
L 30 × 30 × 31.360.91
L 40 × 40 × 42.421.63
L 45 × 45 × 53.382.27
L 50 × 50 × 53.772.53
L 50 × 50 × 64.473
L 60 × 60 × 65.423.64
L 70 × 70 × 77.384.96
L 75 × 75 × 88.996.04
L 80 × 80 × 89.636.47
L 90 × 90 × 912.28.2
L 100 × 100 × 101510.08
L 120 × 120 × 1221.614.51
L 150 × 150 × 1533.822.71
L 200 × 200 × 2059.940.25
L 250 × 250 × 2593.262.63
L 300 × 300 × 3013389.37
European L unequal angles (a selection; every size is in the picker)
Sectionkg/mlb/ft
L 100 × 65 × 78.775.89
L 100 × 65 × 911.17.46
L 120 × 80 × 812.28.2
L 120 × 80 × 101510.08
L 150 × 90 × 1018.212.23
L 150 × 100 × 101912.77
L 150 × 100 × 1222.515.12
L 200 × 100 × 102315.46
L 200 × 100 × 1533.822.71
L 250 × 90 × 1231.220.97
L 250 × 90 × 1640.927.48
US L angles (a selection; every size is in the picker)
Sectionlb/ftkg/m
L5×3×1/46.69.82
L5×3×3/89.814.58
L5×3-1/2×1/213.620.24
L5×5×3/812.318.3
L5×5×1/216.224.11
L6×4×3/812.318.3
L6×4×1/216.224.11
L6×6×3/814.922.17
L6×6×1/219.629.17
L6×6×3/428.742.71
L7×4×1/217.926.64
L8×4×1/219.629.17
L8×6×1/22334.23
L8×8×1/226.439.29
L8×8×3/438.957.89
L8×8×15175.9

The ideal model, (A + B − t) × t, comes close for angles because two effects nearly cancel: the root fillet inside the corner adds steel and the rounded toes at the leg ends take some away. For ISA 50 × 50 × 6 it gives 4.43 kg/m, 1.4% below the 4.49 kg/m in the table; for L5×5×1/2 the gap is 0.2%. Mills roll to their own radii, so two tables can list the same European size 0.1 kg/m apart. IS 808 Tables 10 and 12 add supplementary sizes, which are in the picker as well. Table masses are nominal: delivered bars vary within the rolling tolerances of the product standard (EN 10056-2 for European angles, ASTM A6 for US angles).

Sources

  • Bureau of Indian Standards, IS 808:2021 (fourth revision), Tables 9 and 10 (equal leg angles) and Tables 11 and 12 (unequal leg angles). Public copy: archive.org (Public.Resource.Org).
  • ArcelorMittal and SCI, Orange Book (Eurocode 3, UK National Annex): equal and unequal leg angle tables, dimensions to EN 10056-1. Cross-checked against the British Steel angle datasheets, which agree within 0.1 kg/m.
  • Steel Dynamics, Inc., Product Catalog released on July 22, 2025: angles L5 to L8, dimensions to ASTM A6.
  • Unit conversion with exact factors: 1 lb = 0.45359237 kg and 1 ft = 0.3048 m, so 1 lb/ft = 1.488164 kg/m.

The calculation, without hidden assumptions

Pick a named rolled angle (ISA equal or unequal from IS 808:2021, European L angles or US L angles) and the calculator uses its published mass per metre, or choose custom legs and thickness to estimate an ideal sharp-corner L-section. For a named angle the result also shows the ideal-model figure and its gap to the table, which stays small for angles: the root fillet adds a little steel and the rounded toes take a little away. Custom mode still exposes the overlap correction and supports metric and imperial inputs.

How to use this calculator

1

Pick an angle series and size, or choose Custom dimensions and enter both outside leg lengths (equal values for an equal angle).

2

Enter thickness and piece length, then choose metric or imperial units.

3

Use 7,850 kg/m³ for carbon-steel estimating or enter a documented density for another material.

4

Optionally enter rate/kg, target mass or a supplier kg/m value.

5

Check the substituted working before using the estimate for procurement.

Where people use it

  • •Estimate equal and unequal angle takeoff mass.
  • •Convert angle mass between kg/m and lb/ft.
  • •Estimate batch weight and material cost for fabrication.
  • •Reverse a target payload or order mass into whole pieces.
  • •Compare ideal geometry with a supplier or standard-table kg/m value.
  • •Look up kg/m and lb/ft of ISA, European L and US L angles without leaving the calculator.

50 × 50 × 5 mm angle, 6 m × 10 pieces

Ideal sharp-corner area is (50 + 50 − 5) × 5 = 475 mm². At 7,850 kg/m³ that is 3.72875 kg/m, about 22.37 kg per 6 m piece and 223.73 kg for 10 pieces.

What the result does not assume

  • •Rolled angles have root and toe radii; ideal rectangular-leg geometry does not reproduce every standard table exactly.
  • •Named-angle masses are nominal table values from the cited standard or mill; delivered bars vary within rolling tolerances, so invoices may use weighed or certified mass.
  • •Density varies by alloy and grade.
  • •This is a mass/procurement calculator, not a structural capacity or code-compliance calculator.
  • •Galvanizing, coatings, holes, cuts and fabrication can change delivered mass.

Frequently asked questions

What is the weight of a 50 × 50 × 6 angle per metre?+

An ISA 50 × 50 × 6 weighs 4.49 kg/m under IS 808:2021, so a 6 m length weighs 26.94 kg. The European L 50 × 50 × 6 weighs 4.47 kg/m, and the thinner L 50 × 50 × 5 weighs 3.77 kg/m.

How much does a 75 × 75 × 6 MS angle weigh?+

IS 808:2021 gives ISA 75 × 75 × 6 6.86 kg/m and ISA 75 × 75 × 8 9 kg/m. A 6 m bar of the 6 mm angle weighs 41.16 kg. The unequal ISA 75 × 50 × 6 weighs 5.68 kg/m.

How much does an L5×5×1/2 angle weigh per foot?+

An L5×5×1/2 weighs 16.2 lb/ft (24.11 kg/m): two 5 in legs, 1/2 in thick. A 20 ft length weighs 324 lb. The catalog used here lists US angles from L5 to L8; for smaller US sizes, use custom dimensions.

What is the formula for angle weight?+

For an ideal constant-thickness L-section, area is (A + B − t) × t. Multiply area by density for mass per length, then by cut length and quantity.

Does it calculate unequal angles?+

Yes. Enter different leg A and leg B dimensions. Equal angles simply use the same value for both legs.

Why is my supplier kg/m different?+

Rolled angles have a root fillet and rounded toes, and each mill rolls to its own radii and tolerances, so two tables can differ by about 0.1 kg/m for the same size. Pick the series your supplier quotes under Section to use that table directly.

Can I use inches and feet?+

Yes. Leg dimensions can be entered in inches and piece length in feet; results still report both kg/m and lb/ft.

Can I calculate pieces from a target weight?+

Yes. Enter a target mass and the calculator reports how many whole pieces of the entered length fit within it.

Is this suitable for structural design?+

No. Mass geometry does not establish grade, section properties, buckling resistance, connection design or code compliance.

Semantic next steps

Continue the calculation

These links move to a different input, formula or project stage rather than a keyword variation of this page.

Everyday Planning Calculators

Flat Bar Weight Calculator — kg/m, lb/ft & Batch Weight

Calculate steel, stainless, aluminum or custom flat bar weight from width, thickness and length. Get kg/m, lb/ft, batch/order mass, cost and target-piece reverse solving.

Hollow Section Weight Calculator — SHS & RHS kg/m

Calculate square or rectangular hollow section weight from outside dimensions, wall, length and density. Get kg/m, lb/ft, batch mass, cost and supplier variance.

Pipe Weight Calculator — kg/m, lb/ft & Total Weight

Calculate theoretical round pipe or tube weight from actual OD, wall thickness, length and material density. Get kg/m, lb/ft, batch weight, surface area and reverse wall thickness.

Metal Plate Weight Calculator — Steel & Aluminum

Calculate plate or sheet weight from length, width, thickness and material density. Get kg/lb, batch weight, kg/m², cost, reverse target thickness and measured-density diagnostics.

Steel Grating Weight Calculator — kg/m² & lb/ft²

Steel grating, 30 × 3 mm bars at 30 mm pitch: 23.55 kg/m² (4.823 lb/ft²) before cross bars. Enter your bar size and pitch for kg/m², lb/ft² and panel weight.

Rebar Weight Calculator — kg/m, lb/ft & Tonnes

Calculate theoretical rebar/TMT bar weight from diameter, cut length and quantity. Get kg/m, lb/ft, tonnes, allowance, cost and reverse bars by target mass.

Gross Weight Calculator — Net to Gross Shipment Weight with Cartons & Pallets

Turn net product weight into gross shipment weight: add unit packaging, carton tare, pallets and other packing, round to whole cartons, and get carton-mark weights, a per-pallet average and kg and lb totals for the packing list.

Bend Allowance Calculator — K-Factor, Deduction & Flat Length

Calculate sheet-metal bend allowance, outside setback, bend deduction and single-bend flat length in mm or inches, with reverse K-factor calibration.

Several shapes and metals in one order

More in this calculator collection

Browse nearby calculators in the same topic cluster so related pages reinforce each other instead of sitting as isolated URLs.

Free publisher widget

Put this calculator on your website

Give readers the live calculator without rebuilding the math. Copy the responsive embed in one click, or customize width, height, border and corner radius before publishing. The branded MAXScanner attribution stays visible.

Preview

Calculator embed HTML

Paste this code into your page. Focus the code box to select it manually.

Keep the result connected to the real job

MAXScanner keeps the formula and assumptions beside the result so you can verify the number before using it in a drawing, estimate, specification, worksheet or document. Where a supplier, manufacturer, drawing or applicable standard owns a requirement, that source remains authoritative.

Publisher widget

Embed MAXScanner Calculator

Preview it, choose a layout, copy the HTML, and paste it into WordPress, Webflow, Wix, Squarespace or any page that accepts custom HTML.

Copy-ready HTML

Responsive, lazy-loaded and branded with a visible MAXScanner attribution link.

Open standalone
The widget is free to use and stays updated from MAXScanner. Keep the visible branded attribution intact. Browse all embeddable calculators.