How the cement and sand are worked out
100 m² of 12 mm cement plaster in a 1:4 mix needs about 9.66 bags of 50 kg cement (483 kg) and 1.34 m³ of sand (2.15 tonnes). In a leaner 1:6 mix the same wall takes 6.90 bags and 1.44 m³ of sand. Both figures use the wet volume (area × thickness), a dry-volume factor of 1.27 for the voids in dry mortar and 10% extra for uneven walls and droppings. Published answers for the same wall range from about 8.8 to 11 bags because those two allowances are often hidden; here they are visible, and you can change them along with the bag size and densities.
How to use this calculator
Pick the surface: an internal wall, an external wall or a ceiling. This loads a typical thickness and mix, which you can change.
Enter the total length of the walls and their height, then the area of doors and windows to leave out. For a ceiling or an odd shape, enter the area you measured.
Set the thickness (6, 12, 15 or 20 mm) and the cement : sand ratio (1:3 to 1:6), then choose the cement bag sold where you build.
Read the bags and the sand in m³, ft³ and tonnes, and open the working to see each step with your numbers.
Where people use it
- •Ordering cement and sand to plaster a new room or a whole floor.
- •Checking a mason’s material list before the plaster work starts.
- •Comparing a 12 mm internal coat with a 20 mm external coat on the same house.
- •Working out the sand for a ceiling coat after the walls are done.
Example: a 4 m × 4 m room, 3 m high, internal plaster 12 mm in 1:6
The four walls measure 16 m × 3 m = 48 m². Leaving out a 0.9 × 2.1 m door and a 1.5 × 1.2 m window (3.69 m²) gives 44.31 m². The wet volume is 44.31 × 0.012 = 0.532 m³, and the dry volume with the 1.27 factor and 10% extra is 0.743 m³. Cement is one part in seven: 0.106 m³, or 152.8 kg, which is 3.06 bags of 50 kg, so buy 4. Sand is the other six parts: 0.637 m³ (22.5 ft³, about 1.02 tonnes).
When the estimate needs adjusting
- •Thickness drives everything. Walls that are out of plumb or have deep joints take more than the nominal 12 mm; raise the thickness or the wastage instead of trusting the figure on the drawing.
- •The 1.27 factor and the 10% allowance are estimating conventions, not values from a standard. Some estimators use 1.33, others add 20–30% for rough brickwork.
- •This page covers cement–sand plaster and render. Gypsum plaster, ready-mixed plaster and lime plaster are sold by coverage per bag: use the coverage on the product sheet.
- •Two-coat work (a 12 mm base coat and an 8 mm finish, for example) is two calculations: enter each coat with its own thickness and mix.
Frequently asked questions
How much cement is needed for 100 sq ft of plaster?+
For 12 mm in a 1:4 mix, about 45 kg of cement, or 0.90 of a 50 kg bag, and 4.4 ft³ of sand (199 kg). That uses the 1.27 dry-volume factor and 10% wastage; without the wastage it is 0.82 of a bag.
How many bags of cement are needed for 100 m² of 12 mm plaster?+
About 9.66 bags of 50 kg in 1:4 and 6.90 bags in 1:6, with the 1.27 factor and 10% wastage. A 20 mm external coat in 1:4 needs 16.09 bags for the same area.
Why is 1.27 used in plaster calculation?+
Dry cement and sand occupy more room loose than after mixing with water, because the cement fills the gaps between sand grains. Multiplying the wet volume by about 1.27 gives the loose dry volume to buy. Some estimators use 1.33 and include part of the wastage in it, which is one reason published figures differ.
What is the best cement-sand ratio for plaster?+
A common guide is 1:6 or 1:5 for internal walls, 1:4 for external walls and 1:3 for ceilings and repairs. A richer mix (more cement) is stronger and less porous but more prone to shrinkage cracks, so follow the specification or your engineer.
What thickness should wall and ceiling plaster be?+
Typically 12 mm on internal brick walls, 15–20 mm on external walls (often in two coats), and 6–10 mm on concrete ceilings. Smooth block or concrete walls need less than rough brickwork.
How much sand is needed for plastering per m²?+
At 12 mm, about 0.0134 m³ (21.5 kg) of sand per m² in 1:4 and 0.0144 m³ (23 kg) in 1:6, with the 1.27 factor and 10% wastage. Damp sand bulks by volume, so buy by mass when you can.
Semantic next steps
Continue the calculation
These links move to a different input, formula or project stage rather than a keyword variation of this page.
Brick Calculator — Bricks, Mortar, Cement & Sand
Estimate bricks for one or more walls after opening deductions, then calculate wet and dry mortar, cement bags, sand volume and optional material cost from actual brick dimensions and mortar-joint inputs.
Concrete Mix Calculator: Cement, Sand & Aggregate
Cement bags, sand, coarse aggregate and water for M5–M25 nominal mixes (1:5:10 to 1:1:2) or your own ratio, in m³, ft³ and tonnes, with the IS 456 limits checked.
Concrete Block Calculator: CMU, Mortar & Cost
Count the concrete blocks for one or more walls after door and window openings and waste, then the mortar bags, pallets and optional cost from the real block face, joint and supplier pack data. Grout for the cores is worked out in the block fill calculator.
Paint Calculator — Walls, Ceiling & Coats
Estimate paint volume from room dimensions, exact opening area, separate wall and ceiling coats, product coverage, waste and optional container size and price.
Tile Calculator — Tiles, Boxes and Waste Allowance
Estimate tiles needed from room dimensions and tile size, add a waste allowance, then optionally calculate boxes and simple material cost.
Drywall Calculator — Sheets, Screws, Tape & Joint Compound
Estimate drywall sheets from room dimensions, openings, ceiling choice, panel size and waste, then add editable planning rates for screws, tape, compound and sheet price.
Free publisher widget
Put this calculator on your website
Give readers the live calculator without rebuilding the math. Copy the responsive embed in one click, or customize width, height, border and corner radius before publishing. The branded MAXScanner attribution stays visible.
Calculator embed HTML
Paste this code into your page. Focus the code box to select it manually.
Keep the result connected to the real job
MAXScanner keeps the formula and assumptions beside the result so you can verify the number before using it in a drawing, estimate, specification, worksheet or document. Where a supplier, manufacturer, drawing or applicable standard owns a requirement, that source remains authoritative.